JOLLY VIBES PEEK-A-BOO TUMBLER TUTORIAL! Day 6 of 12 Days of Christmas!

https://youtu.be/QZ_6dJ9-P5o Hey, guys, welcome to day six of my 12 Days of Christmas. Today we have my Jolly Vibes cup. It's got red and green and gold and some holly leaves and berries around and it's this one's very festive out of all the ones I think this is more traditional Christmas it's got the red and green and gold and Holly all of the things this one I did use today's glitter if you have the Advent box today you got either Fireside or cinnamon cider. I used Fireside on this cup. It's the one in the middle of the peekaboos. It's Fireside underneath today's ant bag box. You got one of these red Glitters. They're chunky mixes with iridescent, and they're both pretty. Let's get to the tutorial on this cup. Starting with this 20-ounce skinny cup from hog, taking the lid off, and prepping with modification, we're going to go on with Holly Berry paint. This is a new Christmas limited edition paint, a bright dark red flying sleigh but Santa. Then we're taking Fireside. This is today's Advent box glitter, and it is so pretty. It's a chunky mix with lots of iridescent colors in there, just sprinkling that in like the middle third, and I'm not ombre this towards the outside edges; I'm keeping it almost like a straight line if I can in that center part snow. Then we're going to take Holly in small this is a bright red beautiful glitter, and we're going to sprinkle that all over the rest of the cup top and the bottom, and again, we're not on bringing this in. We're doing that straight line in time. I know I sealed it with some clear spray paint. Once that was dry, I went on with my first layer of epoxy. This is the Artistry one-to-one fast set, and I like to stick to the smaller glitter when there's a chunky glitter in case one gets loose. So I don't have to worry about it moving onto the part with the small glitter, and we're going on with another coat. We can get that chunky glitter really smooth then I cut out this decal. This is an SVG from Etsy. It says Jolly Vibes. It has a little outline around the edge already. It's like if you did two offsets. If that makes sense, first, I'm just taking off the two outer little layers. We're going to transfer that to the cup. I cut out some little holly berries and leaves. I place these around the cup on the Fireside glitter. That's what it looked like. Then I took some metallic gold spray paint from Rust-Oleum, sprayed the center part, covered up the Fireside glitter, and angled it a little bit. We do get a tiny bit of overspray onto the other red, but for the most part, it's in that middle section, and it was raining. I was barely outside my doorway, and I did get some drops on there that ended up making little spots in the paint. Then immediately came in and peeled off the vinyl. I love the metallic paint because it dries fast there then we go on with another layer of epoxy. After that was dry, I cut out a bunch of different versions of this decal, some with offsets and some without. I can layer and stack things as I put them on/ I'm stacking the green Vibes on top of the gold offset on top of the gold spray paint. It's a different, more Shiny Gold. You can still see it. Then with the Jolly, I took it in red, and I'm doing like the first offset in red. Then I do the second offset in Gold, where we have our peekaboo, a red outline, and a gold Outline. For some reason, my h and y were. So off I peeled them off and did another one. I did it separately. It would be easier to place each letter individually, so that's what I did with the. Gold, I cut out more of the berries and leaves with an offset so that we have a little outline of green for the leaves. Then I do the same thing: we have little red berries outside. I wish for the Christmases, then put those on the same way, lining it up and placing it on March. What's the difference? Then go on with another layer of Epoxy, and once that is all smoothed on there, I'm taking a golden hour. It's a chunky custom mix, and I'm just sprinkling it a little bit on the red parts I fed a little bit of something extra. I went a little heavy-handed and wiped it off in a second but added a beautiful gold Sparkle. Then I did one more layer of epoxy to finish the cup, which is how it turned out over the Fireside glitter peeking through orangey red. That's it for this video.